第一次加工四轴工件遇到问题

yang1218

刀路应该 没问题，进给一直跳像卡顿一样，我用的是马扎克机床，A轴，求大佬帮帮忙{:cry:}

蓝天/白云

提刀后不要用圆弧 快速移动，这主要是后处理和机台不匹配的原因

且行且珍惜、

试过快速g0用g1模式吗？

骚然

程序头加个M46试试

心随行动*

程序发出来看一下，或者机床卡顿的视频等

wanghaining123

MAZAK就这样的，公差不要太小，切削补长不要太小

why6666133

心随行动* 发表于 2020-10-25 19:52
程序发出来看一下，或者机床卡顿的视频等

我也遇到同样的问题了，程序里有很多A，每转一个A角度就会卡一下，nikken转台.机床brother

why6666133

心随行动* 发表于 2020-10-25 19:52
程序发出来看一下，或者机床卡顿的视频等

（nikken）日研分度转台是不是不能联动加工

why6666133

心随行动* 发表于 2020-10-25 19:52
程序发出来看一下，或者机床卡顿的视频等

G91 G28 Z0.0
G28 Y0.
T03 M06
M01
(ToolName=BALL3-R1.5 D.=3.00 R.=1.50)
G00 A281.922 B0.0
G55 G00 G90 X0. Y0.
S2500 M03
G90 X37.596 Y-.359
G43 Z59.999 H03
Z8.999
G01 Z6.537 F1200.
X37.6 Y-.382 Z6.279
X37.603 Y-.407 Z6.13
X37.634 Y-.62 Z5.093
X37.635 Y-.622 Z4.773
X37.625 Y-.557 Z4.459
X37.606 Y-.427 Z4.166
X37.579 Y-.238 Z3.908
X37.544 Y0.0 Z3.697
X37.513 Z3.55 A278.442
X37.484 Z3.39 A274.937
X37.461 Z3.231 A271.359
X37.442 Z3.071 A267.582
X37.425 Z2.907 A263.476
X37.406 Z2.747 A258.968
X37.389 Z2.608 A254.283
X37.376 Z2.482 A249.506
X37.366 Z2.357 A244.656
X37.36 Z2.227 A239.681
X37.357 Z2.09 A234.505
X37.356 Z1.947 A229.054
Z1.803 A223.199
Z1.728 A220.008
X37.355 Z1.649 A216.57
Z1.565 A212.831
X37.354 Z1.474 A208.719
X37.353 Z1.378 A204.161
Z1.278 A199.117
Z1.179 A193.588
Z1.088 A187.651
X37.354 Z1.01 A181.425
Z.95 A175.056
X37.353 Z.866 A161.424
Z.841 A149.938
X37.354 Z.865 A134.745
X37.357 Z.896 A127.202
X37.368 Z.95 A119.843
X37.387 Z1.023 A112.908
X37.412 Z1.108 A106.53
X37.442 Z1.203 A100.711
X37.488 Z1.303 A95.176

andy1414

控制系統4軸同棟控制能力太弱，降低進給速率會改善