|
|
希望高手可以幫小弟修改此後處理,謝謝各位高手大大....
(此後處理為臥式機床含B軸)
(All cuting time = 3.77 Min.)
%
O0001
G40 G49 G80
G91 G28 Z0.0
N1 (ToolName=D12-30L D=12.00 R=0.00 F=50.00 L=75.00)...希望的位子
(ToolName=D12-30L D=12.00 R=0.00 F=50.00 L=75.00)
T12 M6
T14
G90 G0 G54 X-5.003 Y45.695 S8000 M3
M75
G0 B0.
M74..........................(B軸的鬆開及鎖緊)
G43 H12 Z171.055
Z159.655
G1 Z156.655 F2400. M8
Y44.095
G3 X-.003 Y39.096 I5. J.001
G1 X0.0 Y15.096
X-2.2 Y15.095
Y-15.096
X2.2 Y-15.095
Y15.096
.
.
.
.
.
G0 X48.177 Y-44. S8000 M3
M75
G0 B180.
M74..........................(B軸的鬆開及鎖緊)
Z170.755
Z143.955
G1 Z140.955 F2000.
X37.5
X-37.5
G2 X-44. Y-37.5 J6.5
G1 Y37.5
G2 X-37.5 Y44. I6.5 J0.0
G1 X37.5
G2 X44. Y37.5 I0.0 J-6.5
G1 Y-37.5
G2 X37.5 Y-44. I-6.5 J0.0
G1 X48.3
Z146.955
G0 Z170.755 M5...................(出現於此刀具加工結束的最後面)
M9...................(出現於此刀具加工結束的最後面)
G91 G28 Z0.0
M01......(換刀N碼前出現)
N2
(ToolName=CR8 D=8.00 R=0.00 F=50.00 L=75.00)
T14 M6
T16
G90 G0 G54 X157.255 Y-20.5 S6000 M3
G43 H14 Z42.5
B270.
G98 G81 Z35.3 R42.5 F800.
G98 Y-12.5...................................G98可以不要每行都出現嗎???
G98 Y0.0
G98 Y12.5
G98 Y20.5
G80
G0 Z87.5
M75
G0 B90.
M74..........................(B軸的鬆開及鎖緊)
G98 G81 X-157.255 Y20.5 Z35.3 R42.5 F800.
G98 Y12.5
G98 Y0.0
G98 Y-12.5
G98 Y-20.5
G80
G0 Z117.5 M5
M9...................(出現於此刀具加工結束的最後面)
G91 G28 Z0.0
M01......(換刀N碼前出現)
N3 (ToolName=CR6 D=6.00 R=0.00 F=50.00 L=75.00)
T16 M6
T04
G90 G0 G54 X-29. Y-12.5 S8000 M3
G43 H16 Z163.652
M75
G0 B90.
M74..........................(B軸的鬆開及鎖緊)
G98 G81 X-29. Y-12.5 Z149.955 R155.955 F800.
G98 Y12.5
G98 X29.
G98 Y-12.5
G80
G0 Z163.652 M5...................(出現於此刀具加工結束的最後面)
M9...................(出現於此刀具加工結束的最後面)
G91 G28 Z0.0
M01......(換刀N碼前出現)
N4
.
.
.
.
.
G0 Z170.755 M5...................(出現於此刀具加工結束的最後面)
M9...................(出現於此刀具加工結束的最後面)
G91 G28 Z0.0
G90 G0 G54.1 P48 X0. Y0. B0.
M30
%
|
|
发表于 2017-5-18 22:51:43
