解决NX2312直接建模与加工部分功能错误的办法

LIUSONG1981 · 发表于 2023-12-10 10:38:40

替换原来的许可文件，重新打开软件就可以了。

LIUSONG1981 · 发表于 2023-12-10 19:27:39

zhaoyafei19* 发表于 2023-12-10 16:28
试了，还是有问题等大侠修复

在你原来的许可文件加入以下内容就可以了。
INCREMENT nx_concrete ugslmd 2312.12 permanent uncounted SUPERSEDE \
   DUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
   SIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"
INCREMENT nx_synchronous ugslmd 2312.12 permanent uncounted SUPERSEDE \
   DUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
   SIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"
INCREMENT nx_composites_laser ugslmd 2312.12 permanent uncounted SUPERSEDE \
   DUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
   SIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"
INCREMENT rotary_floor_finish ugslmd 2312.12 permanent uncounted SUPERSEDE \
      DUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
      SIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"
INCREMENT nx_cam_turn_mill ugslmd 2312.12 permanent uncounted SUPERSEDE \
      DUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
      SIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"
INCREMENT nx_quick_rough ugslmd 2312.12 permanent uncounted SUPERSEDE \
      DUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
      SIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"
INCREMENT nx_3d_adaptive_rough ugslmd 2312.12 permanent uncounted SUPERSEDE \
      DUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
      SIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"

cuixuanfeng_hbn · 发表于 2023-12-10 12:50:25

本帖最后由 cuixuanfeng_hbn 于 2023-12-10 12:52 编辑

cuixuanfeng_hbn 发表于 2023-12-10 12:48
还是等等eJonny的完美版吧
我只按照他的，在原来的许可证文件上添加了 dim101513 说的那7行，加工试了 ...

至于你说的这个

1.Manufacturing---Create Operation---mill_contour---3D Adaptive Roughing
2.Manufacturing---Create Operation---mill_planar---Face Mill - Zig. ZigZag
3.Manufacturing---Create Operation---cam_test_new---Floor Finish Barrel Swarf
4.Manufacturing---Create Operation---cam_test_new---Wall Milling without Floor

还是等等eJonny的完美版吧，只能说差不多能用了