UG编程求助编个4轴程序

心随行动*

依风 发表于 2016-8-22 14:52
帮我看看把  版本10。0的

你坐标系没放好

依风

心随行动 发表于 2016-8-22 17:15
你坐标系没放好

好的  我在看看  

依风

心随行动 发表于 2016-8-22 17:15
你坐标系没放好

谢谢  我把旋转轴放在x轴  程序输出是带a轴的   。。。问题是卧加旋转轴矢量在y轴  这样我需要怎样设置参数？

心随行动*

依风 发表于 2016-8-23 08:53
谢谢  我把旋转轴放在x轴  程序输出是带a轴的   。。。问题是卧加旋转轴矢量在y轴  这样我需要怎样设置参 ...

那就绕Y轴旋转，然后改后处理

fangjian012925

Tool D50R6 has tool number zero! Its info is not outputted into to_ini.ini file.
;Start of Program
;
DEF REAL _camtolerance
DEF REAL _X_HOME, _Y_HOME, _Z_HOME, _B_HOME
DEF REAL _F_CUTTING, _F_ENGAGE, _F_RETRACT
;
G40 G17 G710 G94 G90 G60 G601 FNORM
;Start of Path
_camtolerance=.06
_X_HOME=999999.9 _Y_HOME=999999.9 _Z_HOME=999999.9
_B_HOME=0
;
;Operation : CONTOUR_PROFILE
;
TRAFOOF
SUPA G0 Z=_Z_HOME D0
SUPA G0 X=_X_HOME Y=_Y_HOME B=_B_HOME D0
;First Tool
T="D50R6"
M6
MSG("METHOD")
TRAFOOF
SUPA G0 Z=_Z_HOME D0
SUPA G0 X=_X_HOME Y=_Y_HOME B=_B_HOME D0
;Initial Move
G0 B0.0
CYCLE832(_camtolerance,0,1)
COMPOF
TRAORI
G54
G0 X49.998 Y240. Z416.456 S0 D0 M3
;Approach Move
Z386.456
;Engage Move
G1 Z338.879 F250.
X0.0 Z338.426
;Cutting
X-6.191 Z338.37 B358.842
X-12.381 Z338.202 B357.685
X-18.566 Z337.922 B356.527
X-24.745 Z337.53 B355.369
X-30.916 Z337.027 B354.212
X-37.077 Z336.411 B353.054
X-43.227 Z335.685 B351.896
X-49.362 Z334.847 B350.739
X-55.481 Z333.898 B349.581
X-61.583 Z332.839 B348.423
X-67.664 Z331.669 B347.266
X-73.724 Z330.39 B346.108
X-79.76 Z329.001 B344.95
X-85.77 Z327.502 B343.793
X-91.753 Z325.895 B342.635
X-97.706 Z324.18 B341.477
X-103.627 Z322.358 B340.32
X-109.515 Z320.428 B339.162
X-115.367 Z318.391 B338.004
X-121.182 Z316.249 B336.847

依风

fangjian012925 发表于 2016-8-23 09:08
Tool D50R6 has tool number zero! Its info is not outputted into to_ini.ini file.
;Start of Program
...

能发个绕y旋转的后处理给我吗 ？？

fangjian012925

依风 发表于 2016-8-23 09:29
能发个绕y旋转的后处理给我吗 ？？

我这个是西门子卧加的

fangjian012925

fangjian012925 发表于 2016-8-23 11:15
我这个是西门子卧加的

留个QQ好了我发你试试

依风

fangjian012925 发表于 2016-8-23 11:25
留个QQ好了我发你试试

33297883  谢谢