UG后处理出宏程序的问题

今生有你

一梦千秋醉佳人 发表于 2016-7-16 11:41
试了下，不可以，要么无限循环，要么少切

教你1招、以下
G40 G90 G49 G80
G91 G30 Z0.0 M9
M1
N1 T4 M6
M1
(TOOL XD8  D8.00  R0.00  L75.00 TIME:0.20)
(floor_stock=0.000mm  side_stock=0.000mm)
G90 G54 G0 X-101.326 Y56.485 M3 S1200
G43 H4 Z10. M8 T5
Z0        
#1=-1.
#2=-2.
WHILE[#1GE#2]DO1
#1=#1-1.
IF[#1LT#2]THEN#1=#2  加这个绝对可以除的完 比如#1＝-0.9 后现会加一刀 0.1
G1 Z#1 F250.
G41 X-101.5 Y55.5 D4
G3 X-100. Y54. I1.5 J0.0
G1 X100.
G2 X104. Y50. I0.0 J-4.
G1 Y-50.
G2 X100. Y-54. I-4. J0.0
G1 X-100.
G2 X-104. Y-50. I0.0 J4.
G1 Y50.
G2 X-100. Y54. I4. J0.0
G3 X-98.5 Y55.5 I0.0 J1.5
G40 G1 X-98.674 Y56.485
G0 Z10.
X-101.326 Y56.489
这里在加1句{:smile:}
IF[#1EQ#2]GOTO100
END1
N100
G91 G30 Z0.0 M9
G91 G28 Y0.0 M5
M30
(TIME:2.75)
%

893011376

你们是通过什么做的，我现在也在弄这个。手工编就会。

诺然科技

楼主的后处理能分享一下吗？跪求

hai10110

HAODD我有哟

hai10110

宏程序后处理我有，有需要请联系

爱拼才会赢123

我有宏程序后处理，有需要请联系QQ605460401

wzp360124360124

G40 G90 G49 G80
G91 G30 Z0.0 M9
M1
N1 T4 M6
M1
(TOOL XD8  D8.00  R0.00  L75.00 TIME:0.20)
(floor_stock=0.000mm  side_stock=0.000mm)
G90 G54 G0 X-101.326 Y56.485 M3 S1200
G43 H4 Z10. M8 T5
Z0        
#1=-1.
#2=-2.
WHILE[#1GT#2]DO1

G1 Z#1 F250.
G41 X-101.5 Y55.5 D4
G3 X-100. Y54. I1.5 J0.0
G1 X100.
G2 X104. Y50. I0.0 J-4.
G1 Y-50.
G2 X100. Y-54. I-4. J0.0
G1 X-100.
G2 X-104. Y-50. I0.0 J4.
G1 Y50.
G2 X-100. Y54. I4. J0.0
G3 X-98.5 Y55.5 I0.0 J1.5
G40 G1 X-98.674 Y56.485
G0 Z10.
X-101.326 Y56.489
#1=#1-1.
IF[#1LT#2]THEN#1=#2  加这个绝对可以除的完 比如#1＝-0.9 后现会加一刀 0.1
END1
N100
G91 G30 Z0.0 M9
G91 G28 Y0.0 M5
M30
(TIME:2.75)