MASTERCAM 后处理如何修改让半径补偿D 统一

shang-hf · 发表于 2016-6-14 13:32:58

更改前
M6T3
M8
G90G10L12P30R0.00
G0G90G54X50.641Y-55.285S6500M3
G43H3Z100.
Z31.
G1Z27.374F1200.
G41D3X51.641
G3X52.141Y-54.785R.5
G1Y-34.357
G3X50.041Y-32.257R2.1
G1X-2.547
G3X-4.647Y-34.357R2.1
G1Y-75.213
G3X-2.547Y-77.313R2.1
G1X50.041
G3X52.141Y-75.213R2.1
G1Y-54.785
Y-53.785
G3X51.641Y-53.285R.5
G1G40X50.641
G0Z100.

M6T6
M8
G90G10L12P30R0.00
G0G90G54X50.641Y-55.285S6500M3
G43H6Z100.
X-13.88Y-76.255
Z33.
G1Z29.405
G41D6X-12.819Y-75.194
G3X-13.173Y-74.341R.5
G1X-38.488
G2X-42.658Y-70.171R4.17
G1Y-33.269
G3X-43.158Y-32.769R.5
G1G40X-44.158
G0Z100.
需要更改后

M6T3
T6
M8
G90G10L12P30R0.00
G0G90G54X50.641Y-55.285S6500M3
G43H3Z100.
Z31.
G1Z27.374F1200.
G41D30X51.641
G3X52.141Y-54.785R.5
G1Y-34.357
G3X50.041Y-32.257R2.1
G1X-2.547
G3X-4.647Y-34.357R2.1
G1Y-75.213
G3X-2.547Y-77.313R2.1
G1X50.041
G3X52.141Y-75.213R2.1
G1Y-54.785
Y-53.785
G3X51.641Y-53.285R.5
G1G40X50.641
G0Z100.

M6T6
M8
G90G10L12P30R0.00
G0G90G54X-13.88Y-76.255S6500M3
G43H6Z100
Z33.
G1Z29.405
G41D30X-12.819Y-75.194
G3X-13.173Y-74.341R.5
G1X-38.488
G2X-42.658Y-70.171R4.17
G1Y-33.269
G3X-43.158Y-32.769R.5
G1G40X-44.158
G0Z100.
多谢各位大侠了

dhwdxy · 发表于 2016-6-14 21:30:14

后处理程序后，手动更改

ningyangyang* · 发表于 2017-1-18 00:46:41

看我的帖子有你想要的后处理

brook259 · 发表于 2020-10-28 15:04:58

在“if cc_pos$, tloffno$”前加一行“tloffno=30”就行

brook259 · 发表于 2020-10-28 15:05:44

在“if cc_pos$, tloffno$”前加一行“tloffno=30”就行

jaczzb · 发表于 2021-1-9 11:33:44

加上会报错呢？

jaczzb · 发表于 2021-1-9 11:45:56

brook259 发表于 2020-10-28 15:05
在“if cc_pos$, tloffno$”前加一行“tloffno=30”就行

加了会报错，生出的程序刀沿号没有了

09 Jan 2021 11:45:20 AM - PST 行 (1321) - 公式/布尔运算失败(常规消息), , 尚未定义标签[2]
09 Jan 2021 11:45:20 AM - PST 行 (1321) - 公式/布尔运算未正确终止
09 Jan 2021 11:45:20 AM - PST 行 (1321) - 数学计算/公式有错误

wuming199735 · 发表于 2021-1-10 09:44:15

编程的时候修改半径补正使其一样就可以了！

wuming199735 · 发表于 2021-1-10 09:46:07

编程的时候把半径补正全部改为30或者做一个模板提前把所有半径补正都改为30不变，就可以了！

		自动登录	找回密码
密码			立即注册

[求助] MASTERCAM 后处理如何修改让半径补偿D 统一

相关帖子