UG爱好者

标题: 谁会用ug编辑走心机 [打印本页]

作者: 潘子*    时间: 2020-1-11 20:08
标题: 谁会用ug编辑走心机
谁会用ug编辑走心机 求学 求后处理

作者: qiaofeng899    时间: 2020-1-12 08:17
什么是走心机,长什么样
作者: 李金钰    时间: 2020-1-14 13:04
我会,UG编走心机也很方便。
作者: suoman1943    时间: 2020-1-14 14:58
我们都是手工和自动相结合的方式做的,程序要自己接,其实也挺方便的,车加工这一块还是手工方便
作者: 腊月的猴子    时间: 2020-7-10 20:33
我就是用UG做的走心机程序
后处理要自己定制复合自己机床的才行
程序格式如下,
%
O0831(XD-DC01-03-1-MAIN)
M9000
G266A6.05B2.0I0K0S1800W83.5X-1.4Z116.F0.03
M61
G97G99G40M51
G300
M95
/M92
M05
M96
G125
M9010
M8
M9500
M107
M108
M111
M113
M8
T0303(OD55R0.4)
M98P19906
S2500M13P11
G99G18G0X66.0Y0
G0Z-0.15
G00X7.
G99G01X6.F.05
X-2.4F.03
X-.416Z-.105F.05
X3.5Z.5F.02
X6.6Z3.8F.03
G53G0X66.0
M1
M9550
M110
G4U2.0
M111
M9551
T0404(OD55R0.2)
M98P19906
S#969M13P11
G98G1Z-0.03F1500
G99G0X66.0Y0
G0X12.0
G1X7.0F0.06
G1X-0.8F0.04
G1X-0.15F0.03
G65P8901A15.B2.2F0.025
G1X1.0Z-1.F0.06
G41G1X-1.4F0.05
G1Z-0.03F0.03
G01X0.4,R0.1
G01X[2.8+#991]Z0.32,R0.2
G1Z18.0F#970M108
G01X[3.0+#992]Z18.1F0.03
G01Z57.0F#970
G40
G01X[4.0+#993]Z57.5F#970
G01Z66.0
G01X4.2
G01X6.05Z66.5
G1W0.3F0.03
G01X8.0
M109
G1Z57.0F0.06
G1X5.0F0.05
G1X[4+#993]F0.03
G1Z57.627
G01Z62.773
G02X3.779Z62.998R.45
G01X[3.1+#993]Z63.742
G1Z66.0F0.03
G4U0.2
G1X8.0F0.06
G53G0X66.0
M5
M1
T0202(GTX)
G0X66.0Y0
G98G1Z65.0F600
G98G0X16.0
G1X4.2F600
G1Z53.F1000
G1X3.2
G1Z14.F1000
G1X2.9
G1Z-1.F1000
G1X50.0F1500
G1Z54.0F600
G53G0X66.0
M1
T0606(M4P0.5)
M98P19906
G0X66.0Y0
G98G1Z54.0F500
G0X17.0
S600M13P11
G4U1.0
#1=4.0
#33=#1
#2=3.4
#17=0.15
WHILE[#1GT#2]DO1
#1=#1-#17
IF[#1LT#2]THEN#1=#2
G99X[#1+2.]F1.0
#32=[#33-#1]/2*TAN[30.]
G99X#1W#32F0.4
G32Z64.0F0.5
G32U4.0W0.5F0.5
G1X17.0F2.0
G1Z54.0F4.0
END1
G53G0X66.0
M1
T0404(OD55R0.2)
S#969M3P11
G98G1Z65.0F1500
G99G0X66.0Y0
G0X12.0
G1X8.0F0.2
G1X4.0F0.06
G1X3.1F0.02
G1Z66.0F0.03
G4U0.1
M108
G2X[4.0+#994]Z66.6R0.6F0.015
G1Z75.0F#971
G4U0.2
G1X[6+#995]Z75.0,R0.6F0.02
G1Z85.F0.04
G1X16.0F0.2
M109
G98G1Z82.F100
G98G1Z73.F800
G53G0X66.0
M5
M1
T0202(GTX)
G0X66.0Y0
G98G1Z73.F800
G98G0X16.0
G1X4.2F800
G1Z53.F1000
G1X3.2
G1Z14.0F1000
G1X2.9
G1Z-1.F1000
Z-1.F1000
G98G1X50.
G98G1Z80.F1000
G53G0X66.0
M1
T0808(D8R0)
M98P19906
M5
M50
G28H0
G98
S1800M123P12
G4U0.5
G0X66.0Y0C0
G1Z70.0F1000
G0X16.0
G98G1X5.0F600
G98G1Z81.F400
G98G1V-2.F400
G98G1V4.F500
G98G1Y0F500
G98G1X16.0F800
G0C180.
G1Z77.F200
G1Z70.0F700
G98G1X5.0F700
G98G1Z81.0F400
G98G1V-2.F500
G98G1V4.F500
G98G1Y0F500
G98G1X16.0F800
G0C0
G53G0X66.0
M125
M51
M1
T0101(QD2)
M98P19906
G99M8
S2100M13P11
G0X66.0Y0
G98G1Z[#985+#981+#983]F800
G99G0X22.
M108
M107
M9595
M110
G4U0.5
M9596
M111
M56
M54
S2000M13P11
G4U0.2
M53
G1X10.0F0.2
M9597
M20
M58
M9570
M221
G99G1X4.0F0.03
G99G1X8.0F0.08
G99G1W-0.7F0.05
G1X6.0F0.05
G2X4.6W0.7R0.7F0.03
G99G1X4.0F0.04
G1X2.0F0.03
G1X-1.2F0.02
M9571
M220
M13S200P11
M59
M55
M57
M9598
M9599
M97
M98P19910(#989#990)
M98P19913
M30
%
作者: hzz545uxl    时间: 2020-10-23 21:54
腊月的猴子 发表于 2020-7-10 20:33
我就是用UG做的走心机程序
后处理要自己定制复合自己机床的才行
程序格式如下,

什么床子?很多代码看不懂




欢迎光临 UG爱好者 (https://www.ugsnx.com/) Powered by Discuz! X3.2