UG爱好者

标题: c轴超程的处理 [打印本页]

作者: laomei* 时间: 2017-1-5 15:48
标题: c轴超程的处理
本帖最后由 laomei 于 2017-1-5 15:50 编辑

最近在网上看到一个视频，关于双摆头机床c轴超程的处理方法，看完后是没有结果的，原来他是做广告要收费的http://www.chuanke.com/v4898425-200637-1171231.html 大家都知道，双摆头的c轴因为有电缆的连接等是不可能朝一个方向无限旋转的。我试着随便做了一个ca轴的双摆头后置，将c轴行程设置为正负200度，在后处理界面的第四轴配置对话框里的轴限制违例标签下勾选“退刀/重新进刀”，其他几乎没有进行任何修改即保存后处理，仿真后得到很满意的结果。由此才得知软件已经很智能了。

作者: 爱好者1111 时间: 2017-1-5 16:20
厉害了我的哥看看

作者: Jackjiang* 时间: 2017-1-5 17:01
感谢分享

作者: xiaohuo* 时间: 2017-1-5 19:59
分享自己的研究成果，感谢

作者: leilingsun 时间: 2017-1-5 22:52
谢谢分享

作者: qq381541276* 时间: 2017-1-6 08:26

作者: 532563196 时间: 2017-1-22 20:11
楼主在吗？可以教我怎么设置的吗？

作者: ckc517 时间: 2017-5-6 22:01
楼主用的那个版本的UG做的后处理？

作者: 24094929 时间: 2017-5-22 21:44
这羊行吗

作者: 24094929 时间: 2017-5-26 22:18
楼主你的说法可能不，是UG那个版本的后处理器

作者: hunt1985 时间: 2017-6-1 20:20
海德汉双摆头是不行的发那科和西门子可以

作者: 长风破浪会有时 时间: 2018-5-3 23:32
发生的风格

作者: 长风破浪会有时 时间: 2018-5-3 23:33
水电费方式

作者: ttaa904 时间: 2018-7-22 10:41
LZ.能把仿真程序贴出来看看吗？我这个轴限制不会退刀，进刀的。只能通过编制程序时控制

作者: laomei* 时间: 2018-7-22 13:38

ttaa904 发表于 2018-7-22 10:41
LZ.能把仿真程序贴出来看看吗？我这个轴限制不会退刀，进刀的。只能通过编制程序时控制

%
G40 G17 G90 G21
G54
G91 G28 Z0.
T01 M06
S8000 M03
G00 G90 C-90. A30.
X-458.722 Y-3.978
Z394.456
X-427.242
Z339.93
G01 X-426.796 Y-3.883 Z339.159 F240. M08
X-426.37 Y-3.592 Z338.427
X-425.985 Y-3.119 Z337.77
X-425.662 Y-2.489 Z337.222
X-425.416 Y-1.733 Z336.809
X-425.259 Y-0.889 Z336.553
X-425.199 Y0. Z336.466
X-425.101 Y9.137 C-91.231
X-424.806 Y18.271 C-92.463
X-424.315 Y27.395 C-93.694
X-423.629 Y36.507 C-94.925
X-422.746 Y45.603 C-96.157
X-421.669 Y54.677 C-97.388
X-420.396 Y63.726 C-98.62
X-418.93 Y72.745 C-99.851
X-417.27 Y81.731 C-101.082
X-415.417 Y90.679 C-102.314
X-413.372 Y99.586 C-103.545
X-411.137 Y108.446 C-104.776
X-408.711 Y117.256 C-106.008
X-406.097 Y126.012 C-107.239
X-403.296 Y134.71 C-108.47
X-400.308 Y143.346 C-109.702
X-397.135 Y151.915 C-110.933
X-393.778 Y160.414 C-112.165
X-390.24 Y168.839 C-113.396
X-386.522 Y177.186 C-114.627
X-382.625 Y185.452 C-115.859
X-378.551 Y193.632 C-117.09
X-374.303 Y201.722 C-118.321
X-369.881 Y209.719 C-119.553
X-365.289 Y217.619 C-120.784
X-360.528 Y225.419 C-122.016
X-355.601 Y233.114 C-123.247
X-350.509 Y240.702 C-124.478
X-345.255 Y248.179 C-125.71
X-339.842 Y255.541 C-126.941
X-334.272 Y262.785 C-128.172
X-328.548 Y269.908 C-129.404
X-322.672 Y276.906 C-130.635
X-316.647 Y283.776 C-131.866
X-310.475 Y290.515 C-133.098
X-304.16 Y297.12 C-134.329
X-297.705 Y303.588 C-135.561
X-291.112 Y309.916 C-136.792
X-284.385 Y316.1 C-138.023
X-277.527 Y322.138 C-139.255
X-270.54 Y328.028 C-140.486
X-263.428 Y333.766 C-141.717
X-256.195 Y339.35 C-142.949
X-248.843 Y344.777 C-144.18
X-241.376 Y350.045 C-145.411
X-233.798 Y355.151 C-146.643
X-226.112 Y360.094 C-147.874
X-218.322 Y364.869 C-149.106
X-210.43 Y369.477 C-150.337
X-202.442 Y373.914 C-151.568
X-194.36 Y378.178 C-152.8
X-186.188 Y382.267 C-154.031
X-177.93 Y386.18 C-155.262
X-169.59 Y389.914 C-156.494
X-161.172 Y393.469 C-157.725
X-152.679 Y396.842 C-158.957
X-144.116 Y400.031 C-160.188
X-135.486 Y403.036 C-161.419
X-126.793 Y405.854 C-162.651
X-118.042 Y408.485 C-163.882
X-109.237 Y410.927 C-165.113
X-100.381 Y413.18 C-166.345
X-91.479 Y415.242 C-167.576
X-82.534 Y417.112 C-168.807
X-73.551 Y418.789 C-170.039
X-64.535 Y420.273 C-171.27
X-55.488 Y421.563 C-172.502
X-46.416 Y422.658 C-173.733
X-37.323 Y423.558 C-174.964
X-28.212 Y424.262 C-176.196
X-19.088 Y424.77 C-177.427
X-9.955 Y425.082 C-178.658
X-0.818 Y425.198 C-179.89
X8.319 Y425.117 C-181.121
X17.453 Y424.84 C-182.352
X26.579 Y424.367 C-183.584
X35.692 Y423.698 C-184.815
X44.789 Y422.833 C-186.047
X53.865 Y421.773 C-187.278
X62.917 Y420.518 C-188.509
X71.939 Y419.069 C-189.741
X80.928 Y417.426 C-190.972
X89.88 Y415.591 C-192.203
X98.79 Y413.563 C-193.435
X107.655 Y411.345 C-194.666
X116.469 Y408.936 C-195.898
X125.23 Y406.339 C-197.129
X133.934 Y403.554 C-198.36
X142.575 Y400.583 C-199.592
X144.252 Y405.293 Z345.126
G00
G01 X142.609 Y400.677 Z336.639 F10000.
X142.575 Y400.583 Z336.466 F240.
X151.15 Y397.426 C159.177
X159.656 Y394.086 C157.946
X168.088 Y390.564 C156.714
X176.442 Y386.862 C155.483
X184.715 Y382.981 C154.252
X192.903 Y378.923 C153.02
X201.001 Y374.69 C151.789
X209.007 Y370.284 C150.557
X216.916 Y365.707 C149.326
X224.725 Y360.961 C148.095
X232.43 Y356.048 C146.863
X240.027 Y350.971 C145.632
X247.514 Y345.732 C144.401
X254.887 Y340.333 C143.169
X262.142 Y334.777 C141.938
X269.275 Y329.067 C140.707
X276.285 Y323.204 C139.475
X283.166 Y317.192 C138.244
X289.917 Y311.034 C137.012
X296.535 Y304.732 C135.781
X303.015 Y298.289 C134.55
X309.355 Y291.708 C133.318
X315.552 Y284.993 C132.087
X321.604 Y278.146 C130.856
X327.507 Y271.17 C129.624
X333.258 Y264.07 C128.393
X338.856 Y256.847 C127.161
X344.298 Y249.506 C125.93
X349.58 Y242.049 C124.699
X354.701 Y234.481 C123.467
X359.658 Y226.805 C122.236
X364.449 Y219.023 C121.005
X369.071 Y211.141 C119.773
X373.523 Y203.161 C118.542
X377.803 Y195.087 C117.311
X381.908 Y186.923 C116.079
X385.837 Y178.673 C114.848
X389.587 Y170.34 C113.616
X393.158 Y161.928 C112.385
X396.547 Y153.442 C111.154
X399.753 Y144.885 C109.922
X402.774 Y136.261 C108.691
X405.609 Y127.574 C107.46
X408.257 Y118.828 C106.228
X410.716 Y110.027 C104.997
X412.986 Y101.176 C103.766
X415.065 Y92.277 C102.534
X416.952 Y83.336 C101.303
X418.647 Y74.357 C100.071
X420.148 Y65.343 C98.84
X421.455 Y56.299 C97.609
X422.568 Y47.229 C96.377
X423.485 Y38.138 C95.146
X424.207 Y29.028 C93.915
X424.733 Y19.905 C92.683
X425.062 Y10.773 C91.452
X425.196 Y1.636 C90.221
X425.133 Y-7.501 C88.989
X424.873 Y-16.636 C87.758
X424.418 Y-25.762 C86.526
X423.766 Y-34.877 C85.295
X422.919 Y-43.975 C84.064
X421.876 Y-53.054 C82.832
X420.638 Y-62.107 C81.601
X419.207 Y-71.133 C80.37
X417.581 Y-80.125 C79.138
X415.763 Y-89.08 C77.907
X413.753 Y-97.994 C76.675
X411.551 Y-106.863 C75.444
X409.16 Y-115.682 C74.213
X406.579 Y-124.448 C72.981
X403.811 Y-133.157 C71.75
X400.856 Y-141.804 C70.519
X397.716 Y-150.385 C69.287
X394.393 Y-158.898 C68.056
X390.887 Y-167.336 C66.825
X387.201 Y-175.698 C65.593
X383.336 Y-183.978 C64.362
X379.293 Y-192.173 C63.13
X375.076 Y-200.28 C61.899
X370.685 Y-208.294 C60.668
X366.124 Y-216.212 C59.436
X361.393 Y-224.03 C58.205
X356.495 Y-231.744 C56.974
X351.433 Y-239.352 C55.742
X346.208 Y-246.849 C54.511
X340.823 Y-254.231 C53.28
X335.281 Y-261.497 C52.048
X329.584 Y-268.642 C50.817
X323.735 Y-275.662 C49.585
X317.736 Y-282.556 C48.354
X311.591 Y-289.318 C47.123
X305.302 Y-295.948 C45.891
X298.871 Y-302.44 C44.66
X292.303 Y-308.793 C43.429
X285.599 Y-315.003 C42.197
X278.764 Y-321.068 C40.966
X271.8 Y-326.984 C39.734
X264.711 Y-332.75 C38.503
X257.499 Y-338.361 C37.272
X250.168 Y-343.817 C36.04
X242.722 Y-349.114 C34.809
X235.163 Y-354.249 C33.578
X227.496 Y-359.221 C32.346
X219.724 Y-364.027 C31.115
X211.851 Y-368.664 C29.884
X203.879 Y-373.132 C28.652
X195.814 Y-377.427 C27.421
X187.657 Y-381.548 C26.189
X179.415 Y-385.492 C24.958
X171.089 Y-389.259 C23.727
X162.685 Y-392.846 C22.495
X154.205 Y-396.251 C21.264
X145.654 Y-399.473 C20.033
X137.036 Y-402.511 C18.801
X128.354 Y-405.363 C17.57
X119.613 Y-408.028 C16.339
X110.817 Y-410.504 C15.107
X101.97 Y-412.791 C13.876
X93.076 Y-414.887 C12.644
X84.139 Y-416.791 C11.413
X75.162 Y-418.503 C10.182
X66.152 Y-420.021 C8.95
X57.11 Y-421.346 C7.719
X48.042 Y-422.476 C6.488
X38.952 Y-423.411 C5.256
X29.844 Y-424.15 C4.025
X20.723 Y-424.694 C2.793
X11.591 Y-425.041 C1.562
X2.455 Y-425.192 C0.331
X-6.683 Y-425.146 C-0.901
X-15.818 Y-424.905 C-2.132
X-24.945 Y-424.466 C-3.363
X-34.061 Y-423.832 C-4.595
X-43.162 Y-423.003 C-5.826
X-52.242 Y-421.977 C-7.057
X-61.298 Y-420.757 C-8.289
X-70.326 Y-419.343 C-9.52
X-79.321 Y-417.735 C-10.752
X-88.28 Y-415.934 C-11.983
X-97.198 Y-413.94 C-13.214
X-106.071 Y-411.756 C-14.446
X-114.895 Y-409.382 C-15.677
X-123.666 Y-406.818 C-16.908
X-132.38 Y-404.066 C-18.14
X-141.032 Y-401.128 C-19.371
X-149.62 Y-398.005 C-20.602
X-158.138 Y-394.698 C-21.834
X-166.584 Y-391.208 C-23.065
X-174.952 Y-387.538 C-24.297
X-183.24 Y-383.689 C-25.528
X-191.443 Y-379.662 C-26.759
X-199.558 Y-375.461 C-27.991
X-207.58 Y-371.086 C-29.222
X-215.507 Y-366.539 C-30.453
X-223.334 Y-361.823 C-31.685
X-231.058 Y-356.94 C-32.916
X-238.675 Y-351.892 C-34.148
X-246.182 Y-346.682 C-35.379
X-253.575 Y-341.312 C-36.61
X-260.851 Y-335.784 C-37.842
X-268.007 Y-330.1 C-39.073
X-275.039 Y-324.265 C-40.304
X-281.944 Y-318.279 C-41.536
X-288.718 Y-312.147 C-42.767
X-295.36 Y-305.87 C-43.998
X-301.864 Y-299.453 C-45.23
X-308.23 Y-292.896 C-46.461
X-314.453 Y-286.205 C-47.693
X-320.531 Y-279.381 C-48.924
X-326.461 Y-272.429 C-50.155
X-332.24 Y-265.35 C-51.387
X-337.865 Y-258.149 C-52.618
X-343.335 Y-250.829 C-53.849
X-348.646 Y-243.393 C-55.081
X-353.796 Y-235.844 C-56.312
X-358.782 Y-228.187 C-57.543
X-363.603 Y-220.424 C-58.775
X-368.256 Y-212.56 C-60.006
X-372.739 Y-204.597 C-61.238
X-377.049 Y-196.539 C-62.469
X-381.186 Y-188.391 C-63.7
X-385.146 Y-180.156 C-64.932
X-388.929 Y-171.838 C-66.163
X-392.532 Y-163.44 C-67.394
X-395.954 Y-154.967 C-68.626
X-399.192 Y-146.422 C-69.857
X-402.247 Y-137.81 C-71.089
X-405.115 Y-129.134 C-72.32
X-407.797 Y-120.398 C-73.551
X-410.29 Y-111.607 C-74.783
X-412.594 Y-102.764 C-76.014
X-414.707 Y-93.874 C-77.245
X-416.628 Y-84.94 C-78.477
X-418.357 Y-75.968 C-79.708
X-419.893 Y-66.96 C-80.939
X-421.235 Y-57.921 C-82.171
X-422.383 Y-48.855 C-83.402
X-423.335 Y-39.767 C-84.634
X-424.092 Y-30.66 C-85.865
X-424.653 Y-21.54 C-87.096
X-425.018 Y-12.409 C-88.328
X-425.186 Y-3.273 C-89.559
X-425.199 Y0. C-90.
X-425.252 Y0.89 Z336.553
X-425.404 Y1.735 Z336.809
X-425.645 Y2.492 Z337.222
X-425.964 Y3.124 Z337.77
X-426.345 Y3.599 Z338.427
X-426.769 Y3.894 Z339.159
X-427.214 Y3.992 Z339.93
G00
Z394.503
X-458.722
Z495.943
X-251.692 Y0.
G91 Z0.
M30
%

作者: ttaa904 时间: 2018-7-31 21:11

laomei* 发表于 2018-7-22 13:38
%
G40 G17 G90 G21
G54

海德汉的

作者: sunxu365 时间: 2018-12-5 21:13
请问，我的机床就是西门子AC轴，C轴只能转正负200的，A轴是-15到120度。旋转坐标轴超程处理方式设为退刀/重新进刀方式，这个退刀的量在哪里设置呢

作者: laomei* 时间: 2018-12-6 19:26

sunxu365 发表于 2018-12-5 21:13
请问，我的机床就是西门子AC轴，C轴只能转正负200的，A轴是-15到120度。旋转坐标轴超程处理方式设为退刀/ ...

安全距离呀。

作者: sas...... 时间: 2018-12-15 15:42
支持支持自产自销

作者: linqvzjb* 时间: 2019-2-20 09:40
值得的学习

作者: 钃濆ⅷ澧 时间: 2021-6-28 18:58
哥你这个程序有抬刀可是太低了没太高会撞上

作者: deifyj01 时间: 2022-3-8 22:55

钃濆ⅷ澧发表于 2021-6-28 18:58
哥你这个程序有抬刀可是太低了没太高会撞上

兄弟，你知道这个问题怎么处理吗？轴限制里面添加哪些代码？

作者: 649760258 时间: 2022-3-13 11:27

deifyj01 发表于 2022-3-8 22:55
兄弟，你知道这个问题怎么处理吗？轴限制里面添加哪些代码？

这个问题我知道，需要改个代码，

作者: deifyj01 时间: 2022-4-5 19:09

649760258 发表于 2022-3-13 11:27
这个问题我知道，需要改个代码，

教一下，怎么改，谢谢

欢迎光临 UG爱好者 (https://www.ugsnx.com/)